Previous Page | Next Page Contents Glossary Index Configuring the System > Configuration Work Sheets >

Duplex Configuration Work Sheet

Table 29. Configuration Work Sheet - Duplex Models
Item Available Values Selected Values
Duplex Dual Simplex
Printer 1 Printer 2
MESSAGE DISPLAY LANGUAGE:
  • US English
  • Spanish
  • French
  • German
  • Japanese
  • Italian
  • Brazilian Portuguese
  • Chinese Simplified
  • Chinese Traditional
PRINTER CONFIGURATION:
Printer Mode Duplex / Simplex
Auto Start Yes / No
PQE boldness for printer 1 100%
Note:
This value must not be changed.
N/A N/A N/A
PQE boldness for printer 2 100%
Note:
This value must not be changed.
N/A N/A N/A
Printer 1 Counter
(CE Change Only)
0 to 2 000 000 000
N/A N/A N/A
Printer 2 Counter
(CE Change Only)
0 to 2 000 000 000
N/A N/A N/A
Printhead resolution (not all values are supported on all printers)
  • 480 DPI
  • 600 DPI
  • 480/600 DPI
IPDS Resolution
  • Automatic
  • 240 DPI
  • 300 DPI
  • 600 DPI
Font Enhancement
  • Single Byte: Yes / No
  • Double Byte: Yes / No
Yes / No
Jam Recovery Type
  • Use Normal Jam Repositioning
  • Suppress MICR Jam Repositioning
  • Suppress All Jam Repositioning
Font Usage Low / Medium / High
Page Segment Usage Low / Medium / High
Overlay Usage Low / Medium / High
Overlay Cache Yes / No
Input Buffer Size Low / Medium / High
Output Buffer Size Low / Medium / High
Direct Attach Yes / No
NPRO Length 0 to 1200 inches
Auto NPRO at EOF Yes / No
Jam Recovery Point Distance 0 to 500 inches
Form Feed Length (Duplex Mode Only) 17 to 250 inches N/A N/A
Length of Forms Between Transfer Points (Duplex Mode Only) 150 to 800 inches N/A N/A
Front Sheet Sequence (Duplex Mode Only) Front First / Front Second N/A N/A
Verification Marks (Duplex Mode Only) Yes / No N/A N/A
Logical Page Increment 0 to 20 pels
Clear Memory for Security Yes / No
Screen Saver Timeout 0 to 60 minutes
Alarm Suppression Yes / No
Fuser Inactivity Timer 0 to 9 hours
Eject to Front Facing Yes / No
Form Definition Order Yes / No
Stacker Enabled Yes / No
Cut Sheet Emulation
  • None
  • Normal Left-to-Right
  • Normal Right-to-Left
  • Inverted Left-to-Right
  • Inverted Right-to-Left
BTS Installed Yes / No
BTS Enabled Yes / No
Offsetter Installed Yes / No
Offsetter Enabled Yes / No
Offset on Mark Forms Yes / No
3130 Bar Code Compatibility Yes / No
Printer 1 Contrast (CE Change Only) 1 to 7 N/A N/A N/A
Printer 2 Contrast (CE Change Only) 1 to 7 N/A N/A N/A
Printer 1 Preheat (Platen Temperature) (CE Change Only) 1 to 100 N/A N/A N/A
Printer 2 Preheat (Platen Temperature) (CE Change Only) 1 to 100 N/A N/A N/A
Printer 1 Hot Roll (Temperature) (CE Change Only) 1 to 100 N/A N/A N/A
Printer 2 Hot Roll (Temperature) (CE Change Only) 1 to 100 N/A N/A N/A
Printer 1 Oil Rate (CE Change Only) 1 to 100 N/A N/A N/A
Printer 2 Oil Rate (CE Change Only) 1 to 100 N/A N/A N/A
Printer 1 Oil Belt (Speed) (CE Change Only) 1 to 100 N/A N/A N/A
Printer 2 Oil Belt (Speed) (CE Change Only) 1 to 100 N/A N/A N/A
Scan Factory Adjust for Printer 1 (CE Change Only) N/A N/A N/A
Process Factory Adjust for Printer 1 (CE Change Only) N/A N/A N/A
Scan Factory Adjust for Printer 2 (CE Change Only) N/A N/A N/A
Process Factory Adjust for Printer 2 (CE Change Only) N/A N/A N/A
Beam 1 Offset Adjustment for Printer 1 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 2 Offset Adjustment for Printer 1 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 3 Offset Adjustment for Printer 1 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 4 Offset Adjustment for Printer 1 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 5 Offset Adjustment for Printer 1 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 1 Offset Adjustment for Printer 2 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 2 Offset Adjustment for Printer 2 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 3 Offset Adjustment for Printer 2 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 4 Offset Adjustment for Printer 2 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Beam 5 Offset Adjustment for Printer 2 (CE Change Only) 0.0 to 15.9 N/A N/A N/A
Machine Sequence for Printer 1 (CE change on initial configuration only) N/A N/A N/A
Manufacturing Plant for Printer 1 (CE change on initial configuration only) N/A N/A N/A
Machine Sequence for Printer 2 (CE change on initial configuration only) N/A N/A N/A
Manufacturing Plant for Printer 2 (CE change on initial configuration only) N/A N/A N/A
Date and Time (CE Change Only) N/A N/A N/A
HOST ATTACHMENTS CONFIGURATION:
Parallel Channel Attachment:
Parallel Link A Installed Yes / No
Parallel Link B Installed Yes / No
Device Address 00 to FF
Second Channel Static / Dynamic
Data Transfer Protocol Interlocked / Data Streaming
Data Streaming Rate 3.0 / 4.5 MB/sec
Card 1 Slot Position 6 / 8 / Not Installed N/A N/A N/A
Card 2 Slot Position 6 / 8 / Not Installed N/A N/A N/A
ESCON Channel:
ESCON Link A Installed Yes / No
ESCON Link B Installed Yes / No
Device Address 00 to FF
Multi-host Environmental Flag True / False
Card 1 Slot Position 6 / 8 / Not Installed N/A N/A N/A
Card 2 Slot Position 6 / 8 / Not Installed N/A N/A N/A
Token Ring TCP/IP Configuration:
Installed Yes/ No
TCP Port 5001 to 65536
IP Address X.X.X.X where X <= 255
Subnet Mask X.X.X.X where X <= 255
Default Gateway Address X.X.X.X where X <= 255
MTU Size 60 to 4096
Hardware address Cannot be changed N/A N/A N/A
Alternate address X'0' to X'FFFFFFFFFFFF'
Ring Speed 4 or 16
Confine Broadcast Yes/ No
Ethernet TCP/IP Configuration:
Installed Yes/ No
TCP Port 5001 to 65536
IP Address X.X.X.X where X <= 255
Subnet Mask X.X.X.X where X <= 255
Default Gateway Address X.X.X.X where X <= 255
Standard MTU Size 60 to 1500
IEEE8023 MTU Size 60 to 1492
Ethernet Type Standard or IEEE8023
Hardware address Cannot be changed N/A N/A N/A
Alternate address X'0' to X'FFFFFFFFFFFF'
Media Speed
  • Auto Negotiation
  • 100BaseT - Full Duplex
  • 100BaseT - Half Duplex
  • 10BaseT - Full Duplex
  • 10BaseT - Half Duplex
FDDI TCP/IP Configuration:
Installed Yes / No  
TCP Port 5001 to 65536  
IP Address X.X.X.X where X <= 255
Subnet Mask X.X.X.X where X <= 255
Default Gateway Address X.X.X.X where X <= 255  
MTU Size 256 to 4352
Hardware address Cannot be changed N/A N/A N/A
Alternate address X'0' to X'FFFFFFFFFFFF'  
Confine Broadcast Yes / No  
PREPROCESSING/POSTPROCESSING INTERFACE CONFIGURATIONS:
DEVICE Number__________
Printer Number 1 / 2 N/A N/A
Port Number 1 / 2 / 3
Enabled Yes / No
Name 1 to 12 alphanumeric characters (including spaces)
Type
  • Coupled Preprocessor
  • Coupled Postprocessor
  • Advanced Postprocessor - MICR
  • Advanced Postprocessor - SMM (Select Medium Modification)
Characteristics:
Pre/Postprocessor Extended NPRO: 0 to 800 inches
Pre/Postprocessor Busy Timer: 1 to 999 seconds
Postprocessor Tag Type:
  • Coupled
  • RSI Compatible
Distance to Postprocessor
  • 24 to 800 inches
  • 24 to 1200 inches
Postprocessor Error Page Stop 0 to 50 pages
Postprocessor Verify Alignment Page Stop 0 to 5000 pages
Pre/Postprocessor Baud Rate in Kbps 19.2 or 62.5
DEVICE Number__________
Printer Number 1 / 2 N/A N/A
Port Number 1 / 2 / 3
Enabled Yes / No
Name 1 to 12 alphanumeric characters (including spaces)
Type
  • Coupled Preprocessor
  • Coupled Postprocessor
  • Advanced Postprocessor - MICR
  • Advanced Postprocessor - SMM (Select Medium Modification)
Characteristics:
Pre/Postprocessor Extended NPRO: 0 to 800 inches
Pre/Postprocessor Busy Timer: 1 to 999 seconds
Postprocessor Tag Type:
  • Coupled
  • RSI Compatible
  • Advanced
Distance to Postprocessor
  • 24 to 800 inches
  • 24 to 1200 inches
Postprocessor Error Page Stop 0 to 50 pages
Postprocessor Verify Alignment Page Stop 0 to 5000 pages
Pre/Postprocessor Baud Rate in Kbps 19.2 or 62.5
DEVICE Number__________
Printer Number 1 / 2 N/A N/A
Port Number 1 / 2 / 3
Enabled Yes / No
Name 1 to 12 alphanumeric characters (including spaces)
Type
  • Coupled Preprocessor
  • Coupled Postprocessor
  • Advanced Postprocessor - MICR
  • Advanced Postprocessor - SMM (Select Medium Modification)
Characteristics:
Pre/Postprocessor Extended NPRO: 0 to 800 inches
Pre/Postprocessor Busy Timer: 1 to 999 seconds
Postprocessor Tag Type:
  • Coupled
  • RSI Compatible
  • Advanced
Distance to Postprocessor
  • 24 to 800 inches
  • 24 to 1200 inches
Postprocessor Error Page Stop 0 to 50 pages
Postprocessor Verify Alignment Page Stop 0 to 5000 pages
Pre/Postprocessor Baud Rate in Kbps 19.2 or 62.5
DEVICE Number__________
Printer Number 1 / 2 N/A N/A
Port Number 1 / 2 / 3
Enabled Yes / No
Name 1 to 12 alphanumeric characters (including spaces)
Type
  • Coupled Preprocessor
  • Coupled Postprocessor
  • Advanced Postprocessor - MICR
  • Advanced Postprocessor - SMM (Select Medium Modification)
Characteristics:
Pre/Postprocessor Extended NPRO: 0 to 800 inches
Pre/Postprocessor Busy Timer: 1 to 999 seconds
Postprocessor Tag Type:
  • Coupled
  • RSI Compatible
  • Advanced
Distance to Postprocessor
  • 24 to 800 inches
  • 24 to 1200 inches
Postprocessor Error Page Stop 0 to 50 pages
Postprocessor Verify Alignment Page Stop 0 to 5000 pages
Pre/Postprocessor Baud Rate in Kbps 19.2 or 62.5